A Crafts Community For Craft Ideas & DIY Projects - Craftster.org
Help | About | Contact | Press | Advertise | Cookie Policy | Terms | Site Map
Welcome, Guest.
Please login or register.
Craftster Tip:  You can organize your bookmarks into folders!  Read more here.
Total Members: 315,872
Currently Running With Scissors:
422 Guests and 8 Users
Home Craftster Community Crafting Articles Craft Tutorials My Craftster Crafting Calendar City Guides

Jewelry and Trinkets Tutorials

Browse free product instructions and tutorials from the Craftster community. For more crafting fun visit the Jewelry and Trinkets Forum.

November 21, 2004 05:41:23 PM by Ralph
Views: 2814 | Comments: 1
I have seen similiar earings here before, but here's my version.



sorry the pics aren't great, but I think you can get the gist of them.They are made with flattened Bacardi Breezer bottle caps.

Here the basic instructions:

1. Wash and dry bottle caps.

2. Use pliers to gently pull out the 'fluted' edge of the bottle cap.

3. The bottle caps I used had a waxy/rubbery substance in the bottom, you need to remove it to make the bottle caps flat. Run a craft knife or blade around the edge of it, then slice through the thick rim of the substance. You should now be able to pull the substance off the cap.

4. Place the bottle caps face down on a hard surface, you may need to place a piece of thick fabric (I used old jeans) between the caps and the surface to protect them.

5. Use a hammer to flatten the bottle caps.

6. Make holes in the bottle caps to attatch earing findings etc. If you plan on using jump rings keep this in mind when macking the holes to ensure they fit. I used a nail and hammer to make my holes, but I'm sure there is a better way.

7. Attatch earing findings, beads etc to make beautiful earings.

Those intructions might seem a bit odd, I'm not very good at explaining things, if you have any questions, just ask.

-Ralph    

April 07, 2017 11:56:27 AM by oespiritodasartes
Views: 4327 | Comments: 7

This necklace is composed of 16 to 17 units like the one shown below. Each unit was made with superduos, 4x3mm rondelles, 8/0 seed beads and 11/0 seed beads.



These were the steps I used to make each unit.



Interesting fact:The necklace is named after a city in my country. Braga is the oldest city in Portugal and one of oldest Christian cities in the world.  
I created a video tutorial with detailed instructions https://youtu.be/UeG3aqsQGok





February 16, 2015 09:39:43 PM by TheDancingOnes
Views: 28350 | Comments: 12
I'm a jewelry designer, and my favourite thing to work with is leather. I harvest 100% of my leather from used clothing, mostly jackets, skirts and pants from the thrift store. There seem to be infinite possibilities, tons of which I'm still discovering. The marbling trend seems to have really taken off lately, so I decided to try it out on some leather.

The leather I used was harvested from a light camel coloured coat, with a very even nonporous surface. I purchased supplies from www.Dharmatrading.com, which consisted of Alum (mordant), Carrageenan (a thickener), and Angelus Leather Paints.

Here's the process:

1. Begin by dissolving the alum in water, and applying it to the leather in a spray bottle. I don't know if this is recommended for health, but I took a hot iron to the leather until it dried, and repeated the process a couple times, until I was sure it was completely saturated with alum. Alum is a chemical compound, so yeah, I wouldn't recommend ironing it like I did. Just let it dry naturally, then repeat the process with the spray bottle.

2.
I used a large pyrex dish to mix my solution in, but if you have a marbling tub that's even better. The receptacle gets filled 3/4 of the way full with water, then about 2 TBSP of carrageenan gets whisked briskly into the water, careful not to make too many bubbles. Once the solution is thick, the paint can be added to the surface.

3. I used Angelus leather paints for my project. However, these leather paints are not made for marbling, so it took a bit of playing around to get them just right, but I'm quite pleased with how they turned out. Once the paints are floating on the surface, you can take a toothpick and manipulate it, swirling it however pleases you.

4. To transfer the paint to the leather, simply place the flat, prepared leather face side down carefully across the painted surface of the solution. Leave it in contact for a few seconds. Lift the leather, drop it into a cold water bath, and gently shake until the slimy stuff is gone, being careful not to brush any unnecessary paint off the surface. Once it's dry, the paint will be permanent, and the leather can be used however you like. It can be cut into earrings, wrapped and snapped to create bracelets, or sewn into a coin purse.

Check out my pictures below for some project ideas, and to see how the paint floats on the surface.

thanks for reading!
















Craft Tutorials in Jewelry and Trinkets



Powered by MySQL Powered by PHP Powered by SMF 1.1.11 | SMF © 2006-2009, Simple Machines LLC
SimplePortal 2.3.5 © 2008-2012, SimplePortal
Valid XHTML 1.0! Valid CSS!

Help | About | Contact | Press | Advertise | Privacy Policy | Cookie Policy | Terms | Site Map

Copyright ©2003-2017, Craftster.org, © 2009-2018 MH Sub I, LLC dba Internet Brands