Hi all! It has been a pretty busy summer full of travel and the festival season has kept me too busy to post much on here unfortunately. It is starting to slow down now however and I thought it would be nice to share a little sumpin', sumpin' that I made with my Craftster friends. I hope you like it!Before We Get Started.
This attack, while very easy to make, does call for the knowledge of a few basic quilled shapes - if you have never quilled before or need a little refresher, you can find a free attack at http://www.littlecircles.net/quilling-shapes-attack
. This attack also calls for a stacked quilling form (which is very, very easy to make) which you can find the free attack at http://www.littlecircles.net/apps/blog/show/32147013-diy-stacked-quilling-form-attack
. If you don't have the time to make one or just don't want to, you can alternatively use any type of cylindrical objects in the correct diameter Paper.
For this project I used 7 different colors of paper. You could use less colors for the interior petals if you wish but I will list the amounts that I used in the example pictured above. I used Quilled Creations paper for this project which are all 17" long strips.
A) Copper 7 x 17" strips, 12 x 4.25" strips
B) Antique Gold 1 x 17" strip
C) Golden 1 x 8.5" strip, 8 x 4.25" strips
D) Sunset 12 x 4.25" strips
E) Pumpkin 12 x 4.25" strips
F) Deep Yellow 8 x 4.25" strips
G) Watermelon 12 x 4.25" strips
*Don't forget to snip the glue off the ends for a seamless finish.Supplies.
Stacked quilling form (link to make is above) - Alternatively you will need .5", 2" & 2.5" cylinders to use as forms.
2 open jump rings
Cord. For this example I used a natural hemp but I have also used leather.
Jewelry wrapping wire (not pictured)
Wire wrapping tool (not pictured)
Finishing sealer (I used clear enamel with a UV protectant) Make 7 Outer Petals.
Using your stacked quilling form (the 2.5" tier) and one strip of color A, make a closed coil.
For color A, I chose to use a metallic paper. As always with metallic and pearlized papers, be sure to press and hold the paper ends a bit longer than normal to allow the glue time to adhere. Shape Rings Into Teardrops.
Shape each of the closed coils into tear drop petal shapes. Be careful to take not of where the outer paper edge lay and position it at the bottom of the petal so it will be hidden from view when glued to the center.Make Spacers for the O Rings.
Make 2 tight closed coils using your quilling tool and 2 4.25" strips of color E. With small amounts of glue, place and secure each closed coil into the inside peak of two of the outer petal shapes as shown in the photo above.Make the Interior Petal Shapes.
Roll the remaining 4.25" strips in colors C, D, E, F & G, using your quilling tool into open coils. Secure them with glue and shape them into teardrops.
In a random pile of flesh, place 7 or 8 teardrops inside each outer petal. The amount will vary depending on the positions you choose. The petals containing the closed coils for the necklace fastenings will probably only need 6. There may be a few teardrops left over. Once all the shapes are in place, use the tip of your glue bottle or a small dot of glue on the end of a toothpick and slide it between each of the shapes as well as the outer petal. Do not use too much glue! A little dab will do ya!Make the Center.
Using the 2" tier of your stacked quilling form and the 17" strip of color B, make one closed coil ring.
Using the .5" tier of the stacked quilling form and the 8.5" strip of color C, make a closed coil ring.
Make twelve closed coils using your quilling tool and the remaining 4.25" strips of color A.
Place the small closed coil ring inside the larger closed coil ring. Gently slide all twelve of the smallest closed coils in between the two rings. Use the needle tip of your glue or a tooth pick to slide in between all parts to secure.Before Assembling.
Place all seven petals around the center to make sure they will fit nicely before gluing. Depending on how many individual shapes you placed in each petal, it may seem a bit snug. This is no problem. Just shape each petal into a narrower teardrop shape as a whole. Do this with all seven and they will fit just right.
Place as so: two petals on the top, one petal with the closed coil on either side of those two and the remaining three evenly around the bottom. Glue each petal to the center as well as the petals on either side.Finishing.
Before turning your sunflower into a necklace, you will want to seal it in some manner to give it protection from both water and UV rays. Use your favorite method. My personal favor is a clear and thin enamel with a UV protectant. Allow the glue and sealer to dry for several hours before adding the necklace fastenings.Lastly but not Least.
It's time to turn this paper flower into a true piece of wearable art. Using your jewelry pliers, open up each of the O rings wide. I used 7mm, but I would have preferred 8mm. Turn in each end of the ring. When you close them into the closed coil, they will glide in better. Using slight pressure at the sides, press the rings in to create more space at the top.
Loop your cord through one of the jump rings and fold over. Using about 1.5" of wrapping wire, wrap the wire around the cord as pictured below. I use my fingers. Be sure to crimp the ends down with a tool so the wire does not stab you when you wear this necklace. That would be no fun.
Repeat this same process on both the other side as well as the end bits to attach the clasps. The length of the cord you use is entirely up to you and your preference. Hold the necklace up to yourself in front of a mirror before putting on the clasps. I never do this and my necklaces are always too long and I end up re-doing the clasps on shorter lengths. E.v.e.r.y. s.i.n.g.l.e. t.i.m.e.You're Done!Thank You & Happy Rolling,