Here is a tutorial for the fabric boxes.
Fabric Covered Box
Instructions make a 5x5x2 ½ boxSupplies:
¼ yard (9x 45) of two coordinating fabrics
wet cloth for wiping glue
box cutter or exacto knife with new blade
Use an exacto knife or box cutter to cut and label the mattboard to the following sizes.
Outside Top - 5x5 inches
Outside Bottom - 5x5 inches
Inside Top - 4 ¾ x 4 ¾ inches
Inside Bottom - 4 ¾ x 4 ¾ inches
Outside sides (4 pieces) 2 ½ x 5 inches
Inside sides (4 pieces) 2 ¼ x 4 ¾ inchesCutting the batting:
Cut a piece of batting the same size as each piece of mattboard.Cutting the fabric:
Cut a piece of fabric a ½ larger (on all sides) than the outside top and outside bottom mattboard pieces. The four outside side pieces will be covered as one piece. Tape the four outside side pieces together leaving an 1/8 inch gap between them to form one long piece. Cut a piece of fabric ½ larger (on all sides)than the entire strip.
Using the coordinating fabric cut a piece ½ larger (on all sides)than the inside top, inside bottom, and four inside side pieces. Note that the inside side pieces are done separately NOT as one long piece like the outside.Covering the box with fabric:
Begin covering the outside pieces of your box using the fabric you chose for the outside of your box.
One piece at a time, place the fabric on the table (pretty side down), lay a piece of
batting on top of it, then the mattboard on top of the batting. All layers need to be
centered neatly. Glue the four corners neatly in place. This step will help create nice
sharp corners when the box is done. Use a clothespin to hold it in place until it sets.
But dont leave the clothespins on until the glue dries or the clothespin will be glued to your project.
Continue to glue down the four sides of each piece.
Use clothespins as needed until the glue sets.
Cover the four outside side pieces as one long strip.
Using the same method described above, continue to cover the inside pieces of the box using the coordinating fabric. Remember that the inside side pieces are covered individually NOT as one long strip like the outside of the box. Assembling the box:
Make a small fabric hinge the width of the box top from
a scrap of fabric. Attach this to the back of the
outside top piece and the outside side piece.
Make a small tab out of a scrap of ribbon and attach to
the back side of the outside top piece. This will be used to open and close your box.
Continue to glue the inside pieces to the outside pieces. Apply the glue all the way around and close to the edge of each piece and put a line of glue down the middle of each piece. Center each piece neatly. Use the wet towel to wipe an off any glue that leaks out along the edges. Use clothespins to hold in place until the glue sets firmly. If they can be left in place until the glue dries, even better.
Glue the bottom inside and bottom outside pieces together. Use the wet towel to wipe an off any glue that leaks out along the edges. Use clothespins to hold in place until the glue sets firmly. Set aside. Finishing the box:
Remove any clothespins. Fold the outside side pieces around to form the box. Glue the open edge together. . Use the wet towel to wipe an off any glue that leaks out along the edges. Hold this edge in place with a strip of masking tape.
Place glue along the inside edge of the box bottom piece. Center it neatly against the box sides. Use the wet towel to wipe an off any glue that leaks out along the edges. To hold the box in shape while it dries, tape all around the box edges with masking tape. Let the box dry several hours or overnight if possible.
When dry, remove the masking tape. Check all the box edges to make sure the seams are sealed. You can add a dab of glue to any seam that did not seal the first time.
Enjoy your box!!!